Forum Topics Started

Viewing 3 topics - 1 through 3 (of 3 total)
    • Cummins Marine Forum Topics
    • Network problem two engine display on Raymarine

      This topic has 7 replies, has 2 voices, and was last updated byWayne Spalding 4 years ago

      July 20, 2019 at 4:59 am Iā€™m trying to network my two recently installed QSB5.9 version one SIM engines to my Raymarine MFDā€™s. (serial numbers 60294916 & 60295589) I have connected the individual VesselView 4ā€™s to the raymarine backbone via device net cables. The engines are not linked. Only one engine at a time is showing up on the network. The MUS settings are set for stbd master and port slave. VV4ā€™s are port and stbd and different identities ( locations) set. B…

      Started by: Wayne Spalding in: Instrumentation & Electronics

      7 Replies
      September 9, 2019 at 12:50 am Installed a Cummins jumper cable for from Seaboard Marine. ( great price!) MUS jumpers, Port to slave and Stbd to master. Disconnected one VV4 from Raymarine, leaving the other connected to the backbone. Now both engines talking to each other, and only one VV4 communicating with Raymarine, but transmitting both sets of data. Problem was the 2 smartcraft Gateways were competing. Unable to change their addresses without joining the engines, then…

      Last Post by: Wayne Spalding posted: 4 years ago

    • Troll & Cruise modes Vessel View 4

      This topic has 5 replies, has 3 voices, and was last updated byTony Athens 5 years ago

      November 26, 2018 at 4:42 am Hi all, I have a pair of recently installed QSB5.9 380hp with Vessel View 4ā€™s. Troll mode has been displayed in yellow with (apparently no operational effect ) since installation. When I try to disable it, the disable button is greyed out. When the engines were commissioned, the Cummins Tech noticed this, but brushed it off. I would like to know if this feature (Troll rpm) and Cruise mode as per the operating manual is available with these Q…

      Started by: Wayne Spalding in: Instrumentation & Electronics

      5 Replies
      November 26, 2018 at 6:19 pm Wayne, If you figure it out how to incorporate something that is glitch free, reliable, intuitive to use, fulled supported, and something you can troubleshooted if problems occurs, let me know.. At this point in time, those parameters do do exist with my “since 2004” experiences using “Mercury Electronics”, AKA “SmartCraft” or what I am not allowed to call it anymore.in a public forum. Tony

      Last Post by: Tony Athens posted: 5 years ago

    • Vessel View 4 fuel used

      This topic has 2 replies, has 2 voices, and was last updated byWayne Spalding 5 years ago

      October 11, 2018 at 12:53 am I recently installed 2 X QSB 5.9 380 engines into my boat equipped with Vessel View 4 indicators I have no tank quantity indication (I use a dipstick), but note there is good fuel flow indication. Can I set the system up to indicate fuel remaining if I give it the tank capacity of the boat? Or at the least, a ā€˜fuel usedā€™ summary after each trip? Thanks in advance Wayne Spalding Tank quantity ~ 1500ltrs

      Started by: Wayne Spalding in: Instrumentation & Electronics

      2 Replies
      October 11, 2018 at 4:27 pm Thanks Corey, itā€™s the manual input that I was after, there is no level sensor in the tank

      Last Post by: Wayne Spalding posted: 5 years ago

  •  

Viewing 3 topics - 1 through 3 (of 3 total)