Forum Topics Started

Viewing 4 topics - 1 through 4 (of 4 total)
    • Cummins Marine Forum Topics
    • Oil pan plug

      This topic has 7 replies, has 3 voices, and was last updated byMike Pettee 5 years ago

      March 11, 2019 at 6:20 pm Good evening fellas, In the process removing old airseps and installing my new Envirovents on my 330 Diamonds. I’m going to remove the drain back hoses to the pans and need to plug the aft most drain bung in the pan. Looks to be M18x1.5 from the Cummins part diagram. Can anyone confirm that? The coolant plug is npt as well as the combiner block(which is next to go.) I guess it’s just a mixed bag of fasteners. On a side note cleaned …

      Started by: Brian Katz in: Cummins Marine Engines

      7 Replies
      March 14, 2019 at 11:41 am That’s what I was thinking too. Access to that plug is difficult in my setup, so I may just stick a bolt in the walker hose and clamp it.

      Last Post by: Mike Pettee posted: 5 years ago

    • 6bta Date Code

      This topic has 8 replies, has 3 voices, and was last updated byTony Athens 5 years ago

      February 12, 2019 at 8:26 pm I assume this is a date code and serial number? Is it a 2008?? The boats a 2002 so the million dollar question…is it original?

      Started by: Brian Katz in: Cummins Marine Engines

      8 Replies
      February 13, 2019 at 6:11 pm Overall, your aftercooler looks really good, but for sure, it is related to the last water they saw before shut down and then, sitting at the dock for days, weeks & months on end… Use lots of grease during the assembly, and FRESH WATER FLUSH religiously if you are not parking the boat in water that you could use to water your lawn with.. Tony .

      Last Post by: Tony Athens posted: 5 years ago

    • Diesel fuel conditioning

      This topic has 2 replies, has 2 voices, and was last updated byBrian Katz 5 years ago

      October 31, 2018 at 8:53 am As I prepare to winterize my 6TBA’s and as a first time diesel owner I’ve searched the forum looking for information regarding the storage and conditioning of diesel fuel and have not found anything significant. Maybe I’m looking in the wrong place? When using gasoline in other boats I typically use Startron(ethanol treatment) when adding fuel to the boat during the season and Stabil at the time of layup. In short I don’…

      Started by: Brian Katz in: General Discussion

      2 Replies
      November 1, 2018 at 6:15 am Well now its on the books. Thanks Rob.

      Last Post by: Brian Katz posted: 5 years ago

    • 6bta survey? Long Island, NY

      This topic has 3 replies, has 3 voices, and was last updated byBob Patterson 5 years ago

      September 4, 2018 at 7:55 pm I’m looking for a cummins surveyor and some advice for a boat I’m trying to buy in Long Island. I see there are a few guys from my area on here. I am absolutely blown away by the accumulation of knowledge on this sight. Wow. Like many others I can rebuild a smallblock in my sleep but diesel is all new to me. Thanks in advance.

      Started by: Brian Katz in: Cummins Marine Engines

      3 Replies
      September 5, 2018 at 2:21 pm We used Wesco 7 years ago.You get what you pay for.I felt they were very thorough. I think it was Bill who came to do the survey. Good luck with your purchase.Bob

      Last Post by: Bob Patterson posted: 5 years ago

  •  

Viewing 4 topics - 1 through 4 (of 4 total)