Topics Engaged In

Viewing 5 topics - 1 through 5 (of 5 total)
    • Cummins Marine Forum Topics
    • Injection pump removal and install 480ce 6tca

      This topic has 13 replies, has 5 voices, and was last updated bysconrad208 9 months ago

      January 13, 2020 at 5:40 am Hi all need some help with the timing of my injection pump replacement engine is a 2004 480ce 6cta I am looking at cummings manuel and they talk about lining up the pump lock pin and the camshaft lock pin at top dead center. is that all there is to it?? Just line up the pins remove and install the pump ? I understand about tightening the pump drive gear to the pump shaft. just want to make sure i have the timing correct Thanks Larry

      Started by: Lawrence Ross in: Cummins Marine Engines

      13 Replies
      July 4, 2023 at 5:07 am Larry, where did you send your pump to get rebuilt?Ā  did yours have the electronic governor? Ā  I need to send my pump out for rebuild.Ā  also, wanted to confirm the 23 degree setting for this p7100 pump.Ā Ā  thanks steve

      Last Post by: sconrad208 posted: 9 months ago

    • My fresh water flush

      This topic has 17 replies, has 9 voices, and was last updated bywayne 3 years ago

      May 15, 2017 at 3:12 pm Just installed 2 new aftercoolers and at the same time took the opportunity to install fresh water flushing. I do NOT have a water lift muffler and I have a good exhaust design which allowed me to design and install an engine OFF flush system. I had a stainless bung welded into the stainless water pipe between the sea water pump and gear/fuel cooler.Ā  This is the initial install and I will plumb to a manifold so I hook the hose up once and can s…

      Started by: Philip in: Cummins Marine Engines

      17 Replies
      September 13, 2020 at 11:23 pm possibly out the PSS cooling line ? as that would still be open

      Last Post by: wayne posted: 3 years ago

    • Raw water in oil

      This topic has 14 replies, has 8 voices, and was last updated byM. Komar 3 years ago

      October 12, 2017 at 1:55 pm My port engine has raw water in it. I have pressure tested the heat exchanger and I can’t make it leak. How did the water get in there? What a mess.

      Started by: Dan Little in: General Discussion

      14 Replies
      May 4, 2020 at 9:04 am Hey guys, I just had this situation happen with my newly installed last August Cummins 5.9 6BTA 330hp. Oil full off raw water. Flushed engine immediately for the past two days after shutting off raw water. Finally have all clean oil coming out. All signs point to aftercooler failure but have not done further investigation. Engine had 9hrs on it. What was the outcome of the last post? Any suggestions while I try to get the install shop to help?

      Last Post by: M. Komar posted: 3 years ago

    • Exhaust riser

      This topic has 5 replies, has 3 voices, and was last updated bygary 7 years ago

      April 3, 2017 at 4:35 pm i have a pair of 6cta8.3 450 diamonds 2004 . I have dry exhaust with a stainless steel exhaust mixer. Boat spent first 10 years of its life in brackish water. My question is does the mixer require any service? Thanks for your advice in advance.

      Started by: gary in: Cummins Marine Engines

      5 Replies
      April 5, 2017 at 11:50 am

      Last Post by: gary posted: 7 years ago

  •  

Viewing 5 topics - 1 through 5 (of 5 total)