Forum Topics Started

Viewing 6 topics - 1 through 6 (of 6 total)
    • Cummins Marine Forum Topics
    • EnviroVent CCV for QSB5.9

      This topic has 10 replies, has 8 voices, and was last updated byTerry Kerr 2 years ago

      March 6, 2019 at 7:39 am Tony, i currently have the Airsep system on my QSB 380 engines and I read the article on your replacement system and am considering changing mine out to your system. I couldnā€™t find a picture of the QSB with the EnviroVent installed and was curious of how it was installed. Is the oil drain line and checked valve removed and blocked off ? Iā€™m assuming so after reading the article but would like to see an install if possible. Thanks, Troy

      Started by: Troy in: Cummins Marine Engines

      10 Replies
      August 20, 2021 at 2:41 pm If you didn’t get the caps to cap off the hose left over from the the walker Airseps, perhaps the box was not checked when ordering? When ordering the Envirovent CCV, However, it it does ask if you have an existing walker airsep system. I checked “yes” and received the caps in the box.

      Last Post by: Terry Kerr posted: 2 years ago

    • QSB turbo housing

      This topic has 9 replies, has 3 voices, and was last updated byTroy 6 years ago

      March 6, 2018 at 6:05 pm Iā€™m in need of a turbo housing for my 380 qsb, a used one will be fine. Please advise if anyone knows where I can find one. Thanks

      Started by: Troy in: Cummins Marine Engines

      9 Replies
      March 8, 2018 at 6:40 pm Thanks Rob, wasnā€™t looking for any feed back really, I know what caused the issue. This was not my design, itā€™s what they used in another boat. I will be using the stock wet elbows. I am replacing the same model qsb that I have now with newer running take outs. As I posted earlier, the risers were on the engines when I picked them up. I never saw them hooked up in the vessel. Poor craftsmanship was the main culprit, iā€™m just looking for anothe…

      Last Post by: Troy posted: 6 years ago

    • QSB 5.9 oil pans

      This topic has 1 reply, has 2 voices, and was last updated byTony Athens 6 years ago

      February 5, 2018 at 3:45 pm Iā€™m in need of two low profile aluminum oil pans for my qsb 5.9 380 hp engines. The engines I purchased have the deep sump steel pans and are to deep for my engine room. Hoping to find a couple of used ones before I go the new route.

      Started by: Troy in: Cummins Marine Engines

      1 Reply
      February 5, 2018 at 5:53 pm Drop me a note direct & I peek and see what we may have. You will also need different pick up screens.. Curious———-Do you have front or rear sumps now? In case it helps, the deep pans are reversible.. Tony

      Last Post by: Tony Athens posted: 6 years ago

    • Vessel View display cover

      This topic has 2 replies, has 3 voices, and was last updated byCorey Schmidt 7 years ago

      March 18, 2017 at 6:01 am I”m having trouble finding a display cover for my Vessel View, anyone know where i can purchase one ?Ā 

      Started by: Troy in: Instrumentation & Electronics

      2 Replies
      March 20, 2017 at 12:32 pm I think I can find one but I need to see a picture of your display to see which version you have… http://www.sbmar.com/articles/which-cummins-smartcraft-display-do-i-have/Ā 

      Last Post by: Corey Schmidt posted: 7 years ago

  •  

Viewing 6 topics - 1 through 6 (of 6 total)