Description
- Fuel Return Connection
- Fuel Supply Connection
- Oil Pressure Sender Connection
- 1.75″ Raw Water Hose
Understanding Marine Fuel Coolers
First, Letās understand the āwhyā about fuel coolers and what they really do:
Fuel coolers are part of the typical fuel system on most marine electronic engines and are also used as a factory installed option on many non-electronic engines. Itās obvious they are there to cool the heated fuel return flow, but try and realize the actual purpose of why the heat, or EXCESS heat, needs to be removed. We think that fuel cooler application and use should be looked at with an understanding of the system, the āwhy and the howā, thus enabling you to make an informed decision as to whether or not you need to cool your fuel. Remember, we have a saying for all marine applications ā āOne Size NEVER Fits Allā. If you understand the system, then an informed decision can be made for your application:
- Cooler fuel equals denser fuel which can translate into more HP that is available from the engine.
- Cooler fuel, or a more stabilized temp will assure that as the day gets hotter and the fuel tank volume gets lower, you do not see a decrease in MAXIMUM available HP ā Notice I said MAXIMUM HP.
- Comfort ā Imagine having fuel tanks under the floor, especially in a salon area at 140F on a hot summer day.
- Safety & component reliability and longevity ā I doubt you could find a study documenting this, but Iād certainly guess that fuel lines and filters would last longer with 90F fuel passing thru them vs. 140+F fuel running thru them.
- In the case of Cummins Electronic engines & probably some others, (both Common Rail, āCRā, & EUI systems), the supply fuel is used to stabilize or control the max temp of the on-engine ECM ā The fuel supply passes thru the fuel cooled heat-sink that the ECM is part of ā Liquid cooling per se ā¦ā¦.. Cummins has a MAXIMUM SUPPLY temp measured at the inlet of the engine of 140F for their electronic engines (160F for the mechanical engines). That may not sound very cool, but itās cool enough to ensure the ECM has a stabilized temp below what they want to see to assure longevity. But, since rated HP (WOT, full load) is measured at a much lower temp (maybe 70-80F-ish), I doubt you would achieve rated HP on 140F fuel being fed to the engine.
The real impetus to this discussion was about āremoving the coolerā and if this could be done. Actually, we remove many fuel coolers on both CR and EUI engines in our work (well over 100 electronic engine installations in the last 5 yrs) and have no issues whatsoever, but you must understand this is 100% application specific.
Most of our work is commercially orientated and many of the vessels we deal with have very large fuel tanks (100ās to 1000ās of gallons), and thru normal course of circulation, excess heat is safely and comfortably dissipated thru the surfaces of the tanks (like air cooling or thru conduction & convection).
Many of these vessels have integral fuel tanks so a fuel cooler is built into the boat. Think of it like a very large āKeel Coolingā system. I tend to think most steel vessels are built this way regardless of the actual use of the vessel.
Just about all of these vessels cruise at very low HP levels in relation to the HP that is available from the engine. Or, we may install an engine with a much lower rating than the recreational equivalent (maybe a QSM that could be rated at 670-715HP, but we install the 350HP version). Example, an engine rated at 540HP, but which cruises at or has extended running never exceeding 150HP (about 7-8 GPH), would never need a fuel cooler for āHorsepowerā reasons as this would preclude that the operator would NEVER notice any decrease in HP even if the fuel supply approached 140F.
Cummins (and Iād guess most manufacturers) have a max fuel supply temperature NOT TO EXCEED. How you control that fuel supply temperature is not written in stone, at least with Cummins as itās merely a specification or requirement that needs to be met ā With Cummins, the fuel cooler option does not have to be included in a factory ordered engine in many cases ā It can be left to the OEM or end user to decide how he can meet the spec and the application needs.
From our point of view, if a fuel cooler is not needed and the engine manufacturer specification for fuel supply temperature can be met under any condition (most adverse or worst case scenario), then remove it and you will also remove unneeded plumbing and hardware from the engine, besides removing the risk of losing a fuel cooler from an internal failure ā Yes, we have seen many of them fail, some with disastrous contingency damage to the engine. As to our own Seaboard SPEC ā We shoot for 120F as an absolute max in an application where we know it is not needed for any of the reasons mentioned above. Ponder this regarding the need for fuel coolers ā just because a āCERTIFIEDā tech or the mechanic you hired has not seen a CR or any electronic engine without a fuel cooler just tells me he has more to learn, and needs to understand just how and why they may or may not be needed. Do we ever leave factory fuel coolers in place? Of course we do, but again, itās 100% application specific.
FERNANDO DACOSTA –
Do you have one kit for the Cummins 6CTA 450 Diamonds?
Fernando DACOSTA
Douglas (verified owner) –
I have a 6BTA 5.9 M3 Cummins in my 2003 37 Nordic Tug. The kit made the fuel cooler removal a simple project although a bit more work than the video due to engine being in the belly of the boat and connected to fuel supply, return, oil and seawater. I needed to swap out one fitting for my application but still easy. I recommend the kit.
wlsnow100 (verified owner) –
I bought two (2) kits and installed them onto my 6BTA’s (370 hp ea.). Kits were perfect!!! Need i say more??
If you have any questions…fire away. wlsnow100@gmail.com.
Highly recommend them.